Business Cards > Premium Digital > Specialty Business Cards

인쇄 색상은 모니터와 해상도에 따라 실제 색상과 차이가 있을 수 있습니다.

규격
규격	재단사이즈 가로 x 세로 mm 편집사이즈 가로 x 세로 mm
용지

인쇄도수
제작수량		장 x 종

후가공

모서리라운드
누름선
절취선 (미싱)
타공
숫자넘버링 ⓘ		~
박		가로 x 세로 mm
박 (추가1)		가로 x 세로 mm
박 (추가2)		가로 x 세로 mm
형압가공		가로 x 세로 mm
엠보싱(송진)
톰슨가공		가로 x 세로 mm

출고일	예상출고일은 시안확정일 및 인쇄일로 부터 영업일 기준 3~5일 입니다. 후가공이 있을 경우 예상출고일에서 1~3일 추가됩니다. 최선을 다해 출고예상일에 맞추고자 노력하지만 당사 제작 일정에 따라 출고일이 늦어질 수 있습니다. 예상출고일은 한국 영업일 기준이며, 배송 국가의 공휴일 및 통관 사정에 따라 배송이 지연될 수 있습니다.

주문전 유의사항!상세보기 작업방법 안내상세보기

Color

Here are some helpful tips about print colors.

1. Printed colors will appear darker and less vivid than on your monitor.

Printing uses CMYK ink mixing, which works differently from the RGB light on your screen. An exact match between monitor and print is technically not possible.

Files submitted in Spot Color or RGB mode will be automatically converted to CMYK. This conversion results in noticeable color shifts.

In printing, colors may print lighter or darker, and variation between C (Cyan), M (Magenta), Y (Yellow), and K (Black) channels is within normal range.

Even with the same file, color results vary depending on paper type and print timing. This does not constitute grounds for remake.
Large areas of dark background color may show roller marks.
The front and back sides will appear slightly different in tone, even when the same color is used in the design file.

2. Colors with similar CMYK ratios or sensitive tones may print very differently.

Small differences in CMYK values can result in noticeably different printed colors. Color claims are evaluated based on your submitted file only, not the printed result.

Color deviation example: C=61%, M=52%, Y=52%, K=22%

3. K=100% black is processed with overprint enabled.

If you do not want overprint applied, add 1% of another color to the black, or set the value to K=99%.

< Overprint K=100% >

< Overprint Off >

< Rich Black (C=30% + M=30%) >

< Overprint Example >

4. Patterns and textures require sufficient contrast with the background.

We recommend at least 20–30% color difference from the background.

< Color difference 10% >

< Color difference 20% or more >

< Patterns & Textures >

5. Use caution with text and lines made of mixed CMYK colors.

Slight misregistration between color plates may cause colors to spread or shift. This is more noticeable with thinner text and lines.
On dark backgrounds made of mixed CMYK colors, misregistration can cause thin elements to break up or disappear entirely.
For black text and lines, use pure black (K=100%) only. Do not use a mix of CMYK colors.
Even in a single color, extremely thin text or lines may not reproduce clearly in print.

Cutting

Here are some important things to know about the cutting process.

A cutting tolerance of ±1–3mm (0.039–0.118 in) is the industry standard and does not constitute grounds for rework.

Large quantities are cut at once, which causes slight shifting.
Keep important content at least 3mm (0.118 in) inside the trim line on all sides.
For catalogs and pamphlets, at least 5mm (0.197 in) is recommended.
Borders and symmetrical designs cannot be guaranteed to cut evenly. Claims related to this are not accepted.
Shifting may result in slightly diagonal cuts.

Finishing

Here are some things to keep in mind about finishing processes.

A finishing tolerance of ±1–2mm (0.039–0.079 in) is the industry standard and does not constitute grounds for rework.

Die-Cut and Manual Finishing

Due to the nature of high-speed automatic die-cutting, small connection points (nicks) are left on the cut edges to prevent the product from falling out or being damaged.

Die-cutting connection point (nick) example

After die-cutting, a manual finishing process removes any remaining material before shipment.
The number and placement of nicks vary depending on the paper stock, thickness, and shape.
Depending on the paper's texture, thickness, and coating, marks may remain on the cut edges. Thicker paper tends to show more visible marks.
This is a normal result of the manufacturing process, not a product defect.
Flat-printed products such as business cards, hang tags, and coupons will have nicks remaining on the cut edges.
For envelopes and packaging products, nicks are placed to fold inward during assembly. However, depending on the product structure, some may still be visible.

Quantity

Quantity information for dedicated-run printing.

Full quantity or more will be shipped.

InDesign

Size Setup

Select New and set the size for your print product. Set the page size to the trim size, and set the bleed in the Bleed section.

File → New → Document (Ctrl+N)

Intent: Print | Page Size: A4 (210×297mm) | Bleed: 3mm (all sides) | Slug: 0mm

Margin Setup

Set the safety zone in the Margins and Columns dialog. For small products (business cards, hang tags, coupons), use 3mm margins. For larger products (flyers, brochures, catalogs), use 5mm or more.

Layout → Margins and Columns

Margins: 3mm (all sides)

PDF Export

After completing your work, export as PDF with the following settings.

File → Export (Ctrl+E)

Format: Adobe PDF (Print) | Preset: PDF/X-4:2008 | Marks and Bleeds: Use Document Bleed Settings

Illustrator

Size Setup

Select New and set the size for your print product. Set the width and height based on the safety zone size. The trim size adds 3mm to each side (if using 3mm safety zone). The design size adds 6mm total. For small products (business cards, hang tags, coupons), use 3mm safety zone. For larger products (flyers, brochures, catalogs), use 5mm or more.

File → New (Ctrl+N)

Width: 297mm, Height: 210mm + 6mm | Bleed: 6mm (all sides) | Color Mode: CMYK | Raster Effects: High (300 ppi)

Convert Fonts to Outlines

All fonts must be converted to outlines.

Type → Create Outlines (Shift+Ctrl+O)

Outline Stroke

All strokes must be converted to outlines.

Object → Path → Outline Stroke

Overprint

Make sure to uncheck all overprint settings for fills and strokes.

Window → Attributes (Ctrl+F11)

Overprint Fill: unchecked | Overprint Stroke: unchecked

Transparency

Artwork using transparency must be flattened (100% vector).

Object → Flatten Transparency

Raster/Vector Balance: 100 (Vector) | Line Art and Text Resolution: 300 ppi | Gradient and Mesh Resolution: 150 ppi | Convert All Strokes to Outlines: checked

Rasterize

Any gradients, transparency effects, or other effects must be rasterized.

Object → Rasterize

Color Model: CMYK | Resolution: High (300 ppi) | Background: White / Transparent

Document Info Check

Check Document Info for potential print issues. Click Objects in the Document Info panel menu. All items should show "None" — if any show a number (2, 5, etc.), locate and fix those objects using the methods above.

Window → Document Info

Panel menu (☰) → Objects

Photoshop

Size Setup

Select New and set the size for your print product. Set resolution to 300 pixels/inch or higher, and color mode to CMYK. Note: Upscaling a low-resolution source will not improve quality. If your work was done at low resolution, you must recreate it from scratch at high resolution.

File → New (Ctrl+N)

Width: 216mm, Height: 303mm | Resolution: 300 Pixels/Inch | Color Mode: CMYK Color, 8 bit | Background Contents: White

Right-click ruler → Millimeters (or Edit → Preferences → Units & Rulers)

Order Cancellation and Refund

Here is the refund policy for custom-made products.

As all products are custom-manufactured, refunds due to a simple change of mind are not available once production has begun.

If a defect caused by our error is confirmed, please file a claim through our 1:1 inquiry within 5 days of receiving the product. Defect determination is based on our quality standards.

Print errors caused by mistakes in the submitted file are entirely the responsibility of the customer and are not eligible for remake or refund.

Defect determination is based on our quality standards, using a comparison between the submitted file and the printed result.

To request a cancellation, please contact us through our 1:1 inquiry.

Before proof approval

Full refund available.

During production

Refund amount varies depending on production progress and is calculated based on our internal policy.

Before shipment

Product cost is non-refundable. Only shipping fees are refundable for unshipped orders.

Domestic Shipping ▼

결제예정금액

인쇄비	11,600
후가공비	0
Korean VAT	0
배송비	0
Unit Price	$ /ea
합계	$ 12,760
(VAT Included)
* Shipping costs may vary by destination.
12760	3000

공급자	등록번호	119-17-28654
	상호	FORPLI	성명	Jun-Kyu Lee
	소재지	70 Dusan-ro, Geumcheon-gu, Seoul 08595, Korea
	업태	제조업	종목	오프셋인쇄업
	전화번호	+82-2-6677-7330	팩스

옵셋인쇄

소량제작(디지털)

옵셋인쇄

소량제작(디지털)

옵셋인쇄

소량제작(실외용)

옵셋인쇄

마스타인쇄

옵셋인쇄

소량제작(디지털)

옵셋인쇄

견적서

Business Cards > Premium Digital > Specialty Business Cards

FORPLI

파일명	파일크기
마우스로 파일을 끌어오거나 클릭 해주세요.